New Fascia, Wrapped Once and Done for Decades
When the board behind your gutters has gone soft in too many places to splice, replacement resets the whole roof edge. New primed board, aluminum wrap if you want to retire the paintbrush, correct drip edge above, and gutters re-hung straight and true on wood that will hold a screw for the next thirty years.
The Edge That Carries Everything
Fascia has the least glamorous job on the house and the most connections. The roof deck ends on it, the drip edge laps over it, the gutters bolt through it, and the soffit locks into it. When the board is solid, all of those parts pull together as one built edge. When it is rotten, everything attached to it is fastened to mush, and no amount of hardware on the gutter side fixes wood that will not hold a screw. That is the point where replacement stops being an upgrade and becomes the only honest repair.
Utah eaves earn their rot honestly. Five months of snow sitting in gutters, freeze-thaw cycles working every joint, spring runoff finding each gap in a drip edge that was installed short in 1985, and summer sun baking the paint off the south side. On homes we visit, the fascia has often been repainted repeatedly, spliced once or twice, and finally reached the stage where every probe finds another soft spot. The board has done its years. Doing the full run once beats chasing it splice by splice, and the math tips surprisingly early once a ladder is already up.
Replacement is also the moment to end the maintenance cycle permanently. New primed board wrapped in color-matched aluminum never needs paint, sheds water at every seam, and gives the gutter a flat, solid face to hang on. Done alongside soffit replacement or a new roof, the entire edge of the house becomes one continuous, correctly layered system instead of a stack of patches from different decades. If your rot is still local rather than general, start at the fascia repair page and save the full run for when it is earned.
What Full-Run Replacement Includes
Gutters down, board off, edge inspected
The gutters come down carefully, reusable runs set aside, and the old fascia comes off the rafter tails. This exposes the tails and the roof deck edge, the two places eave rot hides. Soft tails get sistered or repaired while they are reachable, photographed and priced before we cut, because burying damaged framing behind new trim is how this job gets done wrong.
New board, primed and properly joined
New fascia goes up straight, joints landing on solid backing, cut ends primed before they meet the sky. A straight fascia line is one of those details nobody consciously notices and everybody reads. Sight down your neighbor’s eave sometime and you will see what a wavy one does to a house.
Aluminum wrap and the drip edge above
Most homeowners choose color-matched aluminum wrap over the new board, bent on site to fit tight and locked so wind cannot work it loose. Above it, the drip edge gets corrected or replaced so water leaving the shingles lands in the gutter instead of curling behind the trim. That one detail is half of why the old board died.
Gutters back on, hung like they mean it
Existing gutters in good shape get re-hung at correct pitch with hidden hangers into the new wood. If the troughs themselves are finished, this is the cheapest possible moment for gutter replacement, and on runs that have failed before, continuous hangers spread the ice load along the entire edge. Finished edges are in the gallery.
Best Done With the Roof or the Gutters
Fascia replacement pairs naturally with a roof replacement, the old drip edge is off anyway and the new edge gets built as one sequence, or with new gutters, since the troughs have to come down regardless. Standing alone it is still a clean two-or-three-day job. We will tell you which grouping saves you real money on your house, and we do not bundle for the sake of the invoice.
Straight Answers From the Ladder
Royal Dane Roofing is a residential-only company out of Salt Lake City, serving the Wasatch Front towns on the service areas page. Jeremy probes the run himself, shows you photos of what the board actually looks like up close, and prices repair against replacement honestly, sometimes the answer is a splice and we say so. Book on the contact page or call (801) 750-4243, Monday through Friday, 7am to 4pm.
Replacement Questions, Answered Straight
What does fascia replacement cost?
It scales with linear footage, eave height, whether the gutters are being reused or replaced, and how much rafter tail repair the tear-off reveals. Wrapping the new board in aluminum adds material cost and subtracts every future paint bill. We measure the runs and give you one firm written number, and it moves only if hidden framing damage appears, with photos and a separate price before we proceed.
Should I wrap the new fascia in aluminum or paint it?
Wrap, for most people. Painted wood fascia in this climate wants fresh paint every five to seven years, and it is the most annoying surface on the house to paint well. Color-matched aluminum wrap seals the board, never peels, and comes in enough colors to match any trim scheme. Painted wood still makes sense on historic homes where the crisp board look matters. We will give you a straight recommendation for yours.
Can you reuse my existing gutters?
Usually, if the troughs are straight and the metal is sound. They come down for the board work and go back up on new wood at corrected pitch, which alone fixes many drainage complaints. If the runs are dented, patched at every seam, or undersized, we will tell you before the job starts so you can decide about replacement while everything is already down. That decision made mid-job costs more than it does on day one.
How long does fascia replacement take?
Most homes run two to three days, gutters down through gutters back up. Rafter tail repairs and complicated rooflines add time, and winter weather can shuffle the schedule. You get the plan in writing before we start and a call the moment anything changes it.
Do soffit and fascia have to be replaced together?
No, but they often deserve to be. They interlock along the same edge, they age in the same weather, and one crew setup covers both. If your soffit is sound we happily replace fascia alone. If both are tired, the combined job costs meaningfully less than two separate visits. The soffit replacement page covers the other half, and the free look covers both regardless.
How do I know it is replacement rather than repair?
Probe results, mostly. Rot in one or two spots with sound board between them is a repair. Soft spots scattered down the run, paint failing everywhere at once, or a board that has been spliced before and is failing again means the whole run is done. We show you exactly what we found and price both paths, and the assessment that answers the question costs nothing.
